CHAPTER ONE
INTRODUCTION
1.0 Background of Study
Corrosion is an irreversible interfacial reaction of a material (metal, ceramic, and polymer) with its environment which results in consumption of the material or in dissolution into the material of a component of the environment. Corrosion could also be defined as the degradation of materials’ properties due to interactions with their environments, and corrosion of most metals (and many materials for that matter) is inevitable of the 105 known chemical elements, approximately eighty are metals , and about half of these can be alloyed with other metals, giving rise to more than 40,000 different alloys. Each of the alloys will have different physical, chemical, and mechanical properties, but all of them can corrode to some extent, and in different ways [1].Corrosion eventually causes failure of components and systems both in the processing andmanufacturing industries and in the service life of many components. Corrosion control of metals and alloys is an expensive process and industries spend huge amounts to control this problem.We have all seen corrosion and know that the process produces a new and less desirable material from the original metal and can result in a loss of function of the component or system. The corrosion product we see most commonly is the rust which forms on the surface of steel.[2]
Figure 1: STEEL RUST
Corrosion is a natural phenomenon. When newly made steel is first exposed to the air, its originally shiny surface will be covered with rust in a few hours. The tendency of metals to corrode is related to the low stability of the metallic state. Metals occur either in the pure metallic state, the zero oxidation state, or in the form of compounds with other elements (they acquire positive states of oxidation. The chemical reactions that take place in corrosion processes are reduction-oxidation (redox) reactions. Such reactions require a species of material that is oxidized (the metal), and another that is reduced (the oxidizing agent). Thus the complete reaction can be divided into two partial reactions: one, oxidation; the other, reduction. In oxidation, the metal loses electrons. The zone in which this happens is known as the anode. In the reduction reaction, the oxidizing agent gains the electrons that have been shed by the metal, and the zone in which this happens is the cathode.[3-5]
Corrosion processes not only influence the chemical properties of a metal but also generate changes in its physical properties and its mechanical behavior. This is why the effects of corrosion are manifested in a variety of forms. The most common form is uniform corrosion, whereby there is a generalized, overall "attack" of the entire exposed surface of the metal, leading to a more or less uniform reduction in the thickness of the affected metal.
Corrosion processes affect many areas of human activity in which metal products are used. In general, as levels of economic development increase, so do costs incurred as a result of corrosion. It is estimated that the costs attributable to the corrosion of metallic materials amount to 4 percent of the gross domestic product of the developed countries. And this cost, representing a loss of resources, would be even higher if methods of protection against corrosion were not so widely applied. It is estimated that because of this protection, populations are able to reduce these potential losses by a factor of about 30 percent.
1.1 Scope of Study
Though the outcome of the project can be applied in nearly all sectors, in the oil and gas industry which have corrosion problem, the scope of this project as have been limited to Corrosion/Corrosion Inhibitors. Thus, corrosion detection and control or reduction techniques have been discussed in detail. Also, within the scope of the project is the overview of the different types of corrosion and corrosion inhibitionand the terrain they occur.
1.2 Significance and Benefits of the Study
Corrosion failures can result to personal injuries, fatalities and cost billions of dollars, through spontaneous shutdown and environmental contamination. Hence, the critical need for better methods to monitor the actual deterioration of a component once it is placed in service in a corrosive environment, analyse that information, and, based on decision-making reasoning, provide a reasonable forecast of the time remaining before maintenance or replacement becomes necessary. Through corrosion inspection and monitoring, the condition of the metals works can always be ascertained and proper corrosion control and maintenance strategies put in place.
Many catastrophic incidences resulting from corrosion failure had been historically recorded.
Corrosion costs the oil and gas industry tens of billions of dollars in lost income and treatment costs every year. The total annual cost of corrosion in the oil and gas production industry is estimated to be $1.372 billion, broken down into $589 million in surface pipeline and facility costs, $320 million in capital expenditures related to corrosion. Corrosion costs US industries alone an estimated $170 billion a year in which the oil and gas industry takes more than half of these costs [6-7]
